Sunnylea is the established pocket of south Etobicoke bounded by Bloor Street West along the north, the South Kingsway along the east, Park Lawn Road along the south, and Royal York Road along the west, with Berry Road threading through the interior. The neighbourhood mixes 1930s-50s original brick centre-hall and bungalow builds with a steady cycle of careful renovations and smaller rebuilds. Glass work here leans toward renovation-scale frameless showers, interior stair guards, and vanity mirrors cut to non-square heritage openings, with every install carrying our 5-year workmanship warranty.
What Sunnylea homes ask of glass
The Sunnylea housing stock is dominated by 1930s-50s original brick centre-hall plans, bungalows, and side-splits on lots of 40 to 60 feet wide. The renovation cycle is now into second-generation territory on much of the stock, and a smaller wave of tear-down rebuilds has been inserted on the deeper lots closer to the South Kingsway. The original ensuites were small or non-existent — many homes did not have an ensuite at all in the original plan — so most projects we are called for are renovation-scale wet zone builds, typically 8 to 12 square metres.
Major corridors anchoring the neighbourhood include Bloor Street West along the north, Royal York Road along the west, the South Kingsway along the east, and Park Lawn Road along the south. Berry Road is the central interior collector. Sunnylea Junior School sits inside the neighbourhood as the central public school anchor , and Sunnylea Park along Berry Road is the standard public landmark.
Frameless shower enclosures in Sunnylea
The Sunnylea primary ensuite shower zone is typically 1.3 to 1.6 metres long with a curbless entry. Frameless shower glass is most often a two- or three-panel run with 10 mm tempered as the standard and 12 mm where a fixed panel exceeds 1.1 metres unsupported. Panel heights are 2.0 to 2.3 metres — the original ceilings in many 1930s-50s Sunnylea homes are lower than current standard, and we adjust panel height accordingly. Templating in Sunnylea is patient work because the original plaster-and-lath walls are rarely true-square — out 8 to 12 mm over a 2.0 metre panel height is common. We template on-site after tile, mark every clip location, and shim, taper, or notch at fabrication. The smaller-house renovation profile also means swing-panel clearance against the vanity face is tighter than on a typical rebuild, and we confirm that clearance at template before we cut. Pricing for Sunnylea shower enclosures sits in the mid range, with the upper range applying when low-iron Starphire is specified.
Glass railings in Sunnylea
Interior stair railings are the main railing category. The original 1930s-50s wood-and-spindle systems are increasingly being replaced with frameless or top-railed glass during the second-generation renovation cycle. The open stair run is usually 3 to 4 metres, and the upper-hall guard along the second-floor landing adds another 2.5 to 4 metres. We base-shoe anchor to the stair stringer and confirm the floor system framing at template — many original 1930s-50s Sunnylea floor systems use narrower joists than current code, and the anchor pattern adjusts accordingly. Exterior rear-deck guards are a smaller category — Sunnylea rear yards are inland and standard residential wind load applies. On homes near the South Kingsway with views toward Humber Bay Park, the railing brief occasionally moves toward exposed-edge structural calcs and laminated glass.
Custom mirrors and partitions in Sunnylea
Vanity mirrors in Sunnylea ensuites are typically 1.6 to 2.2 metres on the vanity wall after renovation — smaller than the rebuild scale because the underlying footprint is more compact. We cut to the wall, polish all visible edges, and back-mount with adhesive and concealed clips. Many Sunnylea openings are not true-square because the original plaster wall isn’t true; we cut to a template rather than to a square dimension. Sconce-through-glass cuts are a steady detail on the wider vanity walls. Basement-bar mirror walls are an occasional secondary category on the renovated 1930s-40s centre-hall homes where the basement has been re-finished as a family room or bar.
Why a recent install in Sunnylea matters
A recent install in Sunnylea was a primary ensuite on a 1948 bungalow that had been renovated to add an ensuite where the original closet stood. The new wet zone was 1.5 metres long with a curbless entry. The fixed panel was 1.0 metre unsupported, so 10 mm tempered. The catch at template was the ceiling — it was 2.05 metres at the wet-zone edge, dropping to 2.02 metres at the curb. We cut the panel to a tapered top edge to maintain a uniform 18 mm clearance under the ceiling rather than letting the panel-top reveal vary. Heritage Sunnylea bungalows demand attention to the small dimensions.
Have a project in Sunnylea?
We do free in-home consults across the GTA. Call 416-897-0767 or message [email protected].
Areas we also serve nearby
- The Kingsway — adjacent north across Bloor
- Old Mill — north-east
- Stonegate-Queensway — adjacent south
- Mimico — south-west
- Swansea — east across the South Kingsway
- Etobicoke pillar
- Frameless shower enclosures
- Glass railings
FAQs about glass work in Sunnylea
Do you serve Sunnylea?
Yes. Sunnylea sits inside our core Etobicoke service area. We’ve worked across the neighbourhood from Bloor Street West down to Park Lawn Road, and from Royal York Road east to the South Kingsway.
How long does a frameless shower take in a Sunnylea renovation?
About two to three weeks. Template 45 to 60 minutes because the heritage walls require careful capture. Fabrication 10 to 14 business days. Install a half- to full day depending on panel count.
What glass thickness do you recommend for a Sunnylea ensuite?
10 mm tempered standard. 12 mm where any fixed panel exceeds 1.1 metres unsupported. Starphire low-iron is the optional upgrade.
Can you work around the lower ceilings in older Sunnylea homes?
Yes. The 1930s-50s ceilings in Sunnylea are often 2.0 to 2.2 metres at the ensuite edge. We adjust panel height to maintain a uniform 15 to 20 mm clearance below the ceiling line and capture any taper at template.